Commit 54a92593 authored by Pedro Henrique Kopper's avatar Pedro Henrique Kopper

Adicionar suporte para caixa de alumínio

parent 61051577
avoid_crossing_perimeters = 1
bed_size = 320,210
bed_temperature = 60
bottom_solid_layers = 1mm
layer_to_pause =
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
build_height = 160
cancel_gcode = G1 X5 Y190 F7200\nG28 X Y
center_part_on_bed = 1
connect_gcode =
cooling = 1
raft_fan_speed_percent = 100
raft_print_speed = 100%
default_acceleration = 0
disable_fan_first_layers = 3
end_gcode = G91\nG1 E-2 F300 ; Recolhe 2mm de Filamento\nM104 S0 ; Desliga aquecimento\nM107 ;Desliga Ventiladores\nG90\nG1 X5 Y205 F7200 ; Movimento Rápido \nG28 X Y ; Recolhe eixos X e Y\n
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 1
extruder_count = 1
extruder_offset = 0x0,0x0,0x0,0x0
baby_step_z_offset = 0
extrusion_axis = E
extrusion_multiplier = 1.15
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_cost = 0
filament_density = 1.24
filament_diameter = 1.75
fill_angle = 45
fill_density = 20%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 75
first_layer_extrusion_width = 100%
first_layer_height = 0.3
first_layer_speed = 30%
recover_first_layer_speed = 10
recover_is_enabled = 0
validate_layer_height = 1
z_homes_to_max = 0
recover_position_before_z_home = 0,0
first_layer_temperature = 205
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
has_fan = 1
has_z_probe = 0
has_z_servo = 0
has_hardware_leveling = 0
has_heated_bed = 0
include_firmware_updater = None
has_power_control = 0
has_sd_card_reader = 0
show_reset_connection = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 70
print_leveling_solution = 3 Point Plane
leveling_manual_positions =
filament_runout_sensor = 0
print_leveling_required_to_print = 0
print_leveling_probe_start = 10
z_probe_z_offset = .1
use_z_probe = 0
z_probe_xy_offset = 0,0
z_probe_samples = 1
z_servo_depolyed_angle = 0
z_servo_retracted_angle = 0
layer_gcode = ; LAYER:[layer_num]
layer_height = 0.2
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
min_skirt_length = 0
notes =
nozzle_diameter = 0.4
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
overhangs = 1
calibration_files = Calibration - Circle.stl
pause_gcode = G1 X5 Y190 F7200
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
external_perimeter_extrusion_width = 100%
perimeter_speed = 30
perimeters = 3
raft_layers = 0
randomize_start = 0
resume_gcode =
retract_before_travel = 20
retract_layer_change = 1
retract_length = 1
retract_length_tool_change = 10
retract_when_changing_islands = 1
retract_lift = 0
retract_restart_extra_toolchange = 0
retract_restart_extra = 0
retract_restart_extra_time_to_apply = 0
retract_speed = 30
resolution = 0
skirt_distance = 6
skirt_height = 1
skirts = 1
brims = 0
slowdown_below_layer_time = 30
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 ; Home de todos os eixos\nG1 Z5 F5000 ; Move a mesa 5mm para baixo\nM104 S[temperature] ; Aquece a [temperature]°C\nM109 S[temperature] ; Aguarda o aquecimento\nG1 E15 F100 ; Extruda 15mm para limpesa do Extrusor\nG92 E0 ; Reseta o Extrusor\nM206 X600 ; Rampa de Aceleração e Desaceleração\n; Powered By 3DCloner ST
write_regex =
read_regex =
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 0
support_material_angle = 45
support_material_infill_angle = 45
support_material_enforce_layers = 0
support_material_extruder = 1
raft_extruder = 0
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = .9mm
support_material_interface_spacing = 0
support_material_pattern = honeycomb
support_material_spacing = 2.5
support_material_speed = 70
support_material_threshold = 0
support_material_z_gap_layers = .3mm
support_material = 1
temperature = 190
extruder_wipe_temperature = 0
bed_remove_part_temperature = 0
thin_walls = 1
threads = 2
toolchange_gcode =
before_toolchange_gcode =
top_infill_extrusion_width = 0
top_solid_infill_speed = 40
top_solid_layers = 1mm
travel_speed = 100
use_firmware_retraction = 0
use_relative_e_distances = 0
baud_rate = 9600
printer_name = 3D Cloner ST
auto_connect = 1
com_port =
vibration_limit = 0
wipe = 0
wipe_tower_size = 0
enable_network_printing = 0
enable_sailfish_communication = 0
ip_address = 127.0.0.1
ip_port = 23
z_offset = 0
feedrate_ratio = 1
extrusion_ratio = 1
bed_shape = 0x0,320x0,320x210,0x210
{
"DocumentVersion": 201606271,
"ID": "8aa9d31a-7f7d-4ec3-be26-75227f0f220a",
"StagedUserSettings": {},
"Macros": [],
"OemLayer": {
"avoid_crossing_perimeters": "1",
"bed_remove_part_temperature": "0",
"bed_shape": "rectangular",
"bed_size": "320,210",
"bed_temperature": "70",
"bottom_clip_amount": "0",
"bridge_acceleration": "0",
"bridge_fan_speed": "100",
"bridge_flow_ratio": "1",
"bridge_speed": "20",
"brim_width": "0",
"build_height": "160",
"cancel_gcode": "G1 X5 Y190 F7200\\nG28 X Y",
"center_part_on_bed": "1",
"complete_objects": "0",
"connect_gcode": "",
"cool_extruder_lift": "0",
"cooling": "1",
"create_raft": "0",
"default_acceleration": "0",
"disable_fan_first_layers": "1",
"end_gcode": "G91\\nG1 E-2 F300 ; Recolhe 2mm de Filamento\\nM104 S0 ; Desliga aquecimento\\nM107 ;Desliga Ventiladores\\nG90\\nG1 X5 Y205 F7200 ; Movimento Rápido \\nG28 X Y ; Recolhe eixos X e Y\\n",
"external_perimeter_extrusion_width": "100%",
"external_perimeter_speed": "70%",
"external_perimeters_first": "0",
"extra_perimeters": "1",
"extruder_clearance_height": "20",
"extruder_clearance_radius": "20",
"extruder_count": "1",
"extruder_offset": "0x0,0x0,0x0,0x0",
"extruder_wipe_temperature": "0",
"extruders_share_temperature": "0",
"extrusion_axis": "E",
"extrusion_multiplier": "1",
"extrusion_width": "0",
"fan_always_on": "0",
"fan_below_layer_time": "60",
"filament_diameter": "3",
"fill_angle": "45",
"fill_density": "0.4",
"fill_pattern": "honeycomb",
"first_layer_acceleration": "0",
"first_layer_bed_temperature": "75",
"first_layer_height": "0.3",
"first_layer_speed": "30%",
"first_layer_temperature": "205",
"g0": "0",
"gap_fill_speed": "20",
"gcode_arcs": "0",
"gcode_comments": "0",
"gcode_flavor": "reprap",
"gcode_output_type": "REPRAP",
"has_fan": "1",
"has_hardware_leveling": "0",
"has_heated_bed": "0",
"has_power_control": "0",
"has_sd_card_reader": "0",
"heat_extruder_before_homing": "0",
"infill_acceleration": "0",
"infill_every_layers": "1",
"infill_extruder": "1",
"infill_extrusion_width": "0",
"infill_first": "0",
"infill_only_where_needed": "0",
"infill_overlap_perimeter": ".06",
"infill_speed": "60",
"infill_type": "TRIANGLES",
"layer_height": "0.4",
"manual_probe_paper_width": ".1",
"max_fan_speed": "100",
"min_extrusion_before_retract": ".1",
"min_fan_speed": "35",
"min_print_speed": "10",
"min_skirt_length": "0",
"notes": "",
"nozzle_diameter": "0.4",
"only_retract_when_crossing_perimeters": "1",
"ooze_prevention": "0",
"output_filename_format": "[input_filename_base].gcode",
"overhangs": "1",
"pause_gcode": "G1 X5 Y190 F7200",
"perimeter_acceleration": "0",
"perimeter_extruder": "1",
"perimeter_extrusion_width": "0",
"perimeter_speed": "30",
"perimeters": "3",
"post_process": "",
"print_center": "160,105",
"print_leveling_method": "Manual",
"print_leveling_required_to_print": "0",
"print_leveling_solution": "3 Point Plane",
"raft_air_gap": ".2",
"raft_extra_distance_around_part": "5",
"raft_extruder": "0",
"raft_fan_speed_percent": "100",
"raft_layers": "0",
"raft_print_speed": "100%",
"randomize_start": "0",
"repair_outlines_extensive_stitching": "0",
"repair_outlines_keep_open": "0",
"resolution": "0",
"resume_gcode": "",
"retract_before_travel": "20",
"retract_layer_change": "1",
"retract_length": "1",
"retract_length_tool_change": "10",
"retract_lift": "0",
"retract_restart_extra": "0",
"retract_restart_extra_toolchange": "0",
"retract_speed": "30",
"show_reset_connection": "0",
"skirt_distance": "6",
"skirt_height": "1",
"skirts": "1",
"slowdown_below_layer_time": "30",
"small_perimeter_speed": "30",
"solid_fill_pattern": "rectilinear",
"solid_infill_below_area": "70",
"solid_infill_every_layers": "0",
"solid_infill_extrusion_width": "0",
"solid_infill_speed": "60",
"solid_shell": "0",
"spiral_vase": "0",
"standby_temperature_delta": "-5",
"start_gcode": "G28 ; Home de todos os eixos\\nG1 Z5 F5000 ; Move a mesa 5mm para baixo\\nM104 S[temperature] ; Aquece a [temperature]°C\\nM109 S[temperature] ; Aguarda o aquecimento\\nG1 E15 F100 ; Extruda 15mm para limpesa do Extrusor\\nG92 E0 ; Reseta o Extrusor\\nM206 X600 ; Rampa de Aceleração e Desaceleração\\n; Powered By 3DCloner ST",
"start_perimeters_at_concave_points": "0",
"start_perimeters_at_non_overhang": "0",
"support_material": "0",
"support_material_angle": "45",
"support_material_enforce_layers": "0",
"support_material_extruder": "1",
"support_material_extrusion_width": "0",
"support_material_infill_angle": "45",
"support_material_interface_extruder": "1",
"support_material_interface_layers": ".9mm",
"support_material_interface_spacing": "0",
"support_material_pattern": "honeycomb",
"support_material_spacing": "2.5",
"support_material_speed": "60",
"support_material_threshold": "0",
"support_material_xy_distance": "0.7",
"support_material_z_distance": "0.15",
"support_material_z_gap_layers": ".3mm",
"support_type": "LINES",
"temperature": "200",
"thin_walls": "1",
"threads": "2",
"toolchange_gcode": "",
"top_infill_extrusion_width": "0",
"top_solid_infill_speed": "50",
"top_solid_layers": "1mm",
"travel_speed": "130",
"use_firmware_retraction": "0",
"use_relative_e_distances": "0",
"vibration_limit": "0",
"wipe": "0",
"wipe_shield_distance": "0",
"wipe_tower_size": "0",
"z_can_be_negative": "0",
"z_offset": "0",
"make": "3D Cloner",
"model": "ST",
"created_date": "2016-12-20T17:57:22.256Z",
"baud_rate": "9600",
"default_material_presets": "PLA",
"windows_driver": "MHSerial.inf",
"calibration_files": "Calibration - Circle.stl",
"oem_profile_token": "ag9zfm1hdHRlcmNvbnRyb2xyQwsSCUFmZmlsaWF0ZRiAgKCq19StCgwLEgZEZXZpY2UYgICAgIDDlQoMCxINRGV2aWNlUHJvZmlsZRiAgICAgNeMCgw",
"active_theme_name": "Red - Dark",
"active_quality_key": "5d8ed633-6c87-462d-98e5-50a1b9e0e5c8"
},
"ActiveQualityKey": "5d8ed633-6c87-462d-98e5-50a1b9e0e5c8",
"MaterialSettingsKeys": [
"378fe860-c0e7-45a3-a3bb-27d621d31344"
],
"UserLayer": {
"printer_name": "3D Cloner ST",
"active_theme_name": "Blue - Light",
"dell-kopper_com_port": "/dev/ttyACM0",
"fill_density": "20%",
"infill_type": "GRID",
"temperature": "190",
"merge_overlapping_lines": "0",
"infill_speed": "70",
"top_solid_infill_speed": "40",
"perimeter_speed": "30",
"external_perimeter_speed": "40",
"support_material_speed": "70",
"bridge_speed": "60",
"travel_speed": "100",
"support_material": "1"
},
"MaterialLayers": [
{
"layer_name": "PLA",
"layer_id": "378fe860-c0e7-45a3-a3bb-27d621d31344",
"filament_diameter": "1.75",
"temperature": "210",
"bed_temperature": "60",
"first_layer_extrusion_width": "100%",
"external_perimeter_extrusion_width": "100%",
"min_print_speed": "10",
"min_fan_speed": "100",
"disable_fan_first_layers": "3",
"extrusion_multiplier": "1.15"
},
{
"layer_name": "ABS",
"layer_id": "945a2da3-766a-424d-bd72-40a6be4d9d33",
"filament_diameter": "1.75",
"filament_density": "1.04",
"temperature": "260",
"bed_temperature": "120",
"first_layer_extrusion_width": "100%",
"external_perimeter_extrusion_width": "100%",
"max_fan_speed": "100",
"disable_fan_first_layers": "3",
"extrusion_multiplier": "1.15",
"min_fan_speed": "100"
},
{
"layer_name": "PETG",
"layer_id": "51b6cb95-7290-4dd3-ab1f-e23aa9b22cad",
"filament_diameter": "1.75",
"filament_density": "1.27",
"temperature": "255",
"bed_temperature": "100",
"first_layer_extrusion_width": "100%",
"external_perimeter_extrusion_width": "100%",
"max_fan_speed": "100",
"disable_fan_first_layers": "3",
"extrusion_multiplier": "1.15",
"min_fan_speed": "100"
}
],
"QualityLayers": [
{
"layer_name": "Media",
"layer_id": "5d8ed633-6c87-462d-98e5-50a1b9e0e5c8",
"layer_height": "0.2",
"fill_density": "30%",
"infill_type": "LINES",
"perimeter_speed": "45",
"external_perimeter_speed": "45",
"travel_speed": "120"
},
{
"layer_name": "Alta",
"layer_id": "07188db0-aa0e-4bb6-bfb1-0c21e95fc616",
"layer_height": "0.1",
"first_layer_height": "0.2",
"fill_density": "40%",
"infill_type": "LINES",
"external_perimeter_speed": "30",
"travel_speed": "120"
},
{
"layer_name": "Baixa",
"layer_id": "b2e15857-1cc7-4213-8504-754d7005b5e7",
"layer_height": "0.3",
"fill_density": "10%",
"infill_type": "LINES",
"infill_speed": "70",
"top_solid_infill_speed": "60",
"perimeter_speed": "60",
"external_perimeter_speed": "60",
"travel_speed": "120"
}
]
}
\ No newline at end of file
This diff is collapsed.
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment